Altinex MULTI-TASKER MT109-102 Manual de usuario

MULTI-TASKER™MANUAL PART NUMBER: 400-0343-003 MT109-1023 IN 1 OUT AUDIO/MIC MIXERFOR MULTI-TASKER™USER’S GUIDE

MULTI-TASKER™400-0343-00399The Group ID is a number representing a group of cards defined with the [WR] command. When using the Group ID, all cards in

MULTI-TASKER™400-0343-00310104. [?CnUi]This command will return general information about the card and its status. It is a function of both the card

MULTI-TASKER™400-0343-00311117. […S] – SAVEThis command will save the configuration command being sent in memory. When sending the command [VLBA12C4

MULTI-TASKER™400-0343-0031212Example:An MT109-102 is in slot #4. Adjust the BASS on the output by sending the command [SELBC4] and then using the [+]

MULTI-TASKER™400-0343-003131319. [LOD1]This command enables the loudness feature.Command Format: [LOD1CnUi]Cn = Card ID (n = slot # from 1 to max slo

MULTI-TASKER™400-0343-0031414Example:Ramp the output volume from a starting level of 1 to a level of 10 for the card in slot #8. Send the command [RUP

MULTI-TASKER™400-0343-0031515Command Format: [RAMP=xCnUi]x = Rate in Seconds4 = 0.25 seconds/step6 = 0.38 seconds /step8 = 0.50 seconds /step10 = 0.6

MULTI-TASKER™400-0343-0031616Some cards require more than one slot in the Multi-Tasker™ system. As an example, some matrix switcher cards require 4 sl

MULTI-TASKER™400-0343-003171734. [RSN]This command reads the slot number of the card with a specified ID number, and returns the value to the system

MULTI-TASKER™400-0343-003181838. [RMG]This command may be used to delete an entire group, or all groups.REMOVE ONE GROUP MEMBERSRemove all the member

MULTI-TASKER™400-0343-00311TABLE OF CONTENTSPagePRECAUTIONS / SAFETY WARNINGS ...2GENERAL...

MULTI-TASKER™400-0343-0031919Example:Group 5 of Unit ID 1 contains the cards in slots 1, 2 and 19. Read the member data for group 5 of Unit ID 1. Se

MULTI-TASKER™400-0343-00320207.4 MENU MODEMENU MODE commands are RS-232 commands that allow virtually the same functionality as programming commands.

MULTI-TASKER™400-0343-0032121Example: 08 (Slot 8): MT109-102NOTE: Only cards supporting the MENU feature will be displayed.5. Find the alphanumeric ch

MULTI-TASKER™400-0343-0032222MT109-102 EXPANDED MENUS1. CONTROL: THIS CARD1: SELECT (Card/Group)CURRENT SELECTION: THIS CARD0: This Card1: Group 12: G

MULTI-TASKER™400-0343-00323233: SET RAMP TIME CURRENT RAMP TIME: 18 SEC1: 04 SEC2: 06 SEC3: 08 SEC4: 10 SEC5: 12 SEC6: 14 SEC7: 16 SEC8: 18 SECESC: GO

MULTI-TASKER™400-0343-00324244. Set Ramp TimeStarting from the main menu, set the ramp time to 10 seconds. Follow the keystrokes below.2 Select SETUP

MULTI-TASKER™400-0343-00325258.3 SOUND DISTORTIONCause 1: Source level is above 0.7Vp-p.Solution1: Make sure that the source level is below 1V p-p. If

MULTI-TASKER™400-0343-00322PRECAUTIONS / SAFETY WARNINGS ... 1Please read this manual carefully before using your MT109-102. Keep this manual hand

MULTI-TASKER™400-0343-00333ABOUT YOUR MT109-102 2MT109-1023 in 1 out Audio Mixer CardThe MT109-102 is a Stereo Audio Mixer Card. When installed in th

MULTI-TASKER™400-0343-00344DESCRIPTION OF MT109-102 4

MULTI-TASKER™400-0343-00355APPLICATION DIAGRAM 5DIAGRAM 1: TYPICAL SETUP

MULTI-TASKER™400-0343-00366DIAGRAM 2: INTERNAL VIEWΣAUDIOLINE/MIC INPUT1BALANCEDAUDIOLINE/MIC INPUT2BALANCEDMICS/WGAINMICS/WGAINS/WGAINPHANTOMPOWERMPC

MULTI-TASKER™400-0343-00377DIAGRAM 3: SWITCH POSITIONSSW1INPUT1LINEMICPHANTOMONOFFLINEINPUT2MICLINEINPUT3MICSW2SW3SW4SW5SW6SW7OFF ONONOFFONOFFONLINE O

MULTI-TASKER™400-0343-00388INSTALLING YOUR MT109-102 6Step 1. Turn off the power to the Multi-Tasker™ enclosure.Step 2. Slide the MT109-102 into an av