Altinex MT101-117 Manual de usuario

MULTITASKER®MANUAL PART NUMBER: 400-0402-003 FRONT PANELS FOR THE 12-SLOT MULTITASKERUSER’S GUIDEMT101-114/115/117The MT101-115 is pictured above.

MULTITASKER400-0402-00397.3 RS-232 CONNECTION7.3.1 RS-232 COMMUNICATIONIf a control system is used to control the cards in the MultiTasker, connect th

MULTITASKER400-0402-003107.4.1 DESCRIPTION OF COMMANDSEach command can consist of up to three parts: Function, Card/Group, and Unit. Card commands re

MULTITASKER400-0402-003113. [RES]The [RES] command resets the enclosure. The controller and all cards in the enclosure will be reset to either their

MULTITASKER400-0402-0031210. [STA1]This command enables automatic feedback from the cards installed in the system and affects any card with auto-feed

MULTITASKER400-0402-00313CONFIGURATION COMMANDSThese commands allow some basic communication properties to be changed as well as access to internal pr

MULTITASKER400-0402-0031422. [BAUD]This command displays the current BAUD rate setting.Command Format: [BAUD]Example:Display the BAUD rate setting b

MULTITASKER400-0402-00315Example:Send the text string "HELLO" to the RS-232 bus. The string will be ignored by the MultiTasker, but not the

MULTITASKER400-0402-00316LED COMMANDSLED commands apply to the MT101-115/117 onlyand are used to control the LED states and retrieve matrix settings b

MULTITASKER400-0402-00317Command Format: {CLFGk}Gk = Group number (k = # from 1-8)See the {CLFC} command for details.34. {STA}This command is used to

MULTITASKER400-0402-00318Example 2:The Key 8 label is SPEAKERS; it is set for volume control, and it is unlocked. The system will return the followin

MULTITASKER400-0402-0031TABLE OF CONTENTSPagePRECAUTIONS / SAFETY WARNINGS... 2GENERAL...

MULTITASKER400-0402-0031937. {CLRK}This command clears the subroutines associated with one or all the keys by setting each to 000. Other key settings

MULTITASKER400-0402-00320Send the command {KFB=1} to enable key feedback. Press Key 1 and then press Key 36. The feedback will be as follows:K01OS10

MULTITASKER400-0402-00321Command Format: {SETVKn}Kn = Key # (n = # from 1 to 36)Example:C2 is an MT109-100 and Key 8 is programmed {WRK8=8,108,0,0,0}

MULTITASKER400-0402-00322SUBROUTINE COMMANDS49. {RDS}This command reads and displays the contentsof one or all subroutines.Command Format: {RDSn}n =

MULTITASKER400-0402-00323After sending the command above, the contents of Subroutine 1 will be as follows:ON1C3, ON2C3, LED1=1,ON3C3, ON4C3MATRIX FUNC

MULTITASKER400-0402-0032452. {PING}This command displays “OK”, but not until after is has been processed through the incoming memory buffer. After do

MULTITASKER400-0402-003257.6. SUMMARY OF COMMANDSSystem Commands1) [VER] Display firmware version2) [SET] Set Unit ID number3) [RES] Reset the system4

MULTITASKER400-0402-003267.7 CONTROL SOFTWAREWindows-(95/98/NT)-based control software is available from the ALTINEX website at www.altinex.com in the

MULTITASKER400-0402-00327Solution 2: Take any other known good card and verify the questionable slot is good by seeing if its LED lights in that slo

MULTITASKER400-0402-0032PRECAUTIONS / SAFETY WARNINGS 1Please read this manual carefully before using your MT101-114/115/117. Keep this manual handy f

MULTITASKER400-0402-0033ABOUT YOUR MT101-114/115/117 2MT101-114/115/117Front Panels for the MultiTasker12-Slot EnclosureThe MT101-114, MT101-115, and

MULTITASKER400-0402-0034PRODUCT DESCRIPTION 4RS-232RS-23236 PROGRAMMABLEBUTTONSRS-232 CONTROLFROM FRONT PANELFROM FRONT PANELRS-232 CONTROLMT101-115/1

MULTITASKER400-0402-0035APPLICATION DIAGRAMS 5DIAGRAM 1 – INSTALLATION INSTRUCTIONSPOWER SUPPLYMake sure the ribbon cable is on this side as shown.10-

MULTITASKER400-0402-0036SYSSELECT OUTPUTS 1-8 for VOLUME ADJ.KEYS 29-36KEYS 13-20SELECT INPUTS 1-8SELECT OUTPUTS 1-8PWRKEYS 21-28VOFFON/V+ADIAGRAM 2 –

MULTITASKER400-0402-0037INSTALLING YOUR MT101-114/115/117 6Step 1. Turn off power to the MultiTasker enclosure and disconnect from AC power.WARNING! A

MULTITASKER400-0402-00387.2 MT101-114/115/117 OPERATIONThis section describes the programming and control functions for the MT101-114, MT101-115,and