MT103
MT103MT103
MT103-
--
-102
102102
102/
//
/1
11
1-
--
-In, 3
In, 3In, 3
In, 3-
--
-Out VGA
Out VGAOut VGA
Out VGA-
--
-Type D
Type DType D
Type DA
AA
A Card
Card Card
Card
User’s Guide
400-0107-006
1
Welcome!
We greatly appreciate your purchase of the MT103-102 1-In, 3-Out
VGA-Type Distribution Amplifier Card. We are sure you will find it reliable
and simple to use. Superior performance for the right price, backed by solid
technical and customer support is what ALTINEX has to offer.
We are committed to providing our customers with
Signal Management Solutions
®
to the most demanding audiovisual
installations at very competitive pricing and we welcome you to join the
ranks of our many satisfied customers throughout the world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your MT103-102 and keep it
handy for future reference. These safety instructions are to ensure the long
life of your MT103-102 and to prevent fire and shock hazards. Please read
them carefully and heed all warnings.
1.1 General
• Qualified ALTINEX service personnel or its authorized representatives
must perform all service.
1.2 Installation Precautions
• Handle the MT103-102 carefully. Dropping or jarring can damage the
card.
• The MT103-102 contains components that are sensitive to electrostatic
discharge (ESD). Always use ESD safety precautions when touching the
card.
• To prevent fire or shock, do not expose this unit to water or moisture.
Do not place the MT103-102 in direct sunlight, near heaters, or
heat-radiating appliances, or near any liquid. Exposure to direct
sunlight, smoke, or steam can harm internal components.
• Do not pull any cables that are attached to the MT103-102.
1.3 Cleaning
• Clean only the connector area with a dry cloth. Never use strong
detergents or solvents such as alcohol or thinner. Do not use a wet cloth
or water to clean the card. Do not clean or touch any component or
PCB.
1.4 FCC Notice
• This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
• This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions found herein, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
• Any changes or modifications to the unit not expressly approved by
ALTINEX, Inc. could void the user’s authority to operate the
equipment.
2. Installation Procedures
Step 1. Turn off power to the MultiTasker
®
system and disconnect from AC power.
Step 2. Remove a slot cover (MT200-101) from one of the unused slots. Identify the slot number and note that it is for RS-232 control.
Step 3. Slide the MT103-102 into the MultiTasker enclosure in order to connect to the bus. Make sure that the card fits into place and then secure the card by
tightening the retainer screws located on the top and bottom of the card.
Step 4. Restore power to the MultiTasker system.
Step 5. The LED on the card panel will turn red indicating that the card is in full operation. A green LED indicates that an input signal is present.
Step 6. Connect a VGA cable from the video source to the input connector of the MT103-102. Connect the output connectors of the MT103-102 to the
display devices through VGA cables.
Step 7. The MT103-102 is now operational.
3. Limited Warranty/Return policies
Please see the ALTINEX website at www.altinex.comfor details on warranty and return policies.
Comentarios a estos manuales