Altinex Multi-Tasker MT103-104 Guía de usuario descargar pdf (Pagina 9)

MULTI-TASKER

8

executed immediately. The path for outputs on

multiple cards or the same card can be loaded.

Command Format: [ONmCnUiP]

m = output number (m =1 to 3)

Cn = card ID No. (n = a slot # from 1 to 19)

(1-8 for MT100-101 or 1-4 for MT100-106)

Ui = unit number (i = # from 0-9)

P = path

Example:

If 2 cards are in slot 6 and 7 of unit 3:

To enable output 1 of card 6 and output 3 of card

7 simultaneously, use the following commands:

[ON1C6U3P]

[ON3C7U3P]

[SW]

If "F" is included use the [ONmCnUiPF] command

or the [ONmCnUiFP]

command.

[ON…..F]: feedback

After processing a command, an OK or ER will be

returned as feedback if "F" is included at the end

of a command string or if the unit ID is zero.

Example:

[ON1C2U3F]: if path is not set

[ON1C2U3PF]: if path is set

6. [OFF]

This command disables one or more outputs of a

single card or a group of cards.

[OFFmCnUiS]: for a single card

This command disables output “m” without

affecting any other outputs.

m = output number (m = 1 to 3)

Cn = card ID No. (n = slot # from 1 to 19)

(1-8 for MT100-101 or 1-4 for MT100-106)

Ui= Unit ID number (i = 0 to 9)

S = saves command to memory

[OFFCnUi]: Turns OFF all outputs of the card

Example:

If card 5 of unit 3 has output 1, 2 and 3 ON:

a)

[OFF1C5U3]: Turns OFF output 1 while output

2 and 3 remain ON.

b)

[OFF23C5]: Turns OFF output 2 and 3.

c)

[OFFC5U3]: Turns OFF all outputs, which is

equivalent to

[OFF123C5U3].

[OFFmGkUiS]: for a group of cards

This command disables output "m" for each card

in group "k" of unit "i".

m = card output (m = # from 1-3)

Gk = group number (k = # from 1-9)

Ui = unit number (i = # from 0-9)

S = saves command to memory

Example:

1. [OFF1G5U1]: Turns OFF output 1 for each

card in group 5 of unit 1.

2. [OFFG5U1]: Turns OFF all outputs for each

card in group 5 of unit 1.

[OFF…..P]: sets path

This command will set the path for the output, but

it is not active until the switch command [SW] is

executed. Commands ending in "P" are not

executed immediately. The path for outputs on

multiple cards or the same card can be loaded.

Command Format: [OFFmCnUiP]

m = number (m =1 to 3)

Cn = card ID No. (n = a slot # from 1 to 19)

(1-8 for MT100-101 or 1-4 for MT100-106)

Ui = unit number (i = # from 0-9)

P = path

Example:

If 2 cards are in slot 6 and 7 of unit 3:

To enable output 1 and 2 of card 6 and output 3

and 4 of card 7 simultaneously, use the following

commands:

1 2 3 4 5 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios