Altinex PE1005 Manual de usuario

SPECIAL APPLICATIONMANUAL PART NUMBER: 400-0384-003 PE1005CONTROL CARD FORPIONEER PLASMA DISPLAYUSER’S GUIDE

SPECIAL APPLICATION400-0384-00396. Click on the “Search” button to check fornew devices on the LAN. NOTE: If you want to assign the IP manually, click

SPECIAL APPLICATION400-0384-00310OPERATION 77.1 RS-232 CONTROL The PE1005 has many advanced remote control capabilities, which are accessible through

SPECIAL APPLICATION400-0384-00311Example:Reset the PE1005 with unit ID 1 to its default settings by sending the command [FRESETC1].The card will displ

SPECIAL APPLICATION400-0384-003127. [RDRL]This command is used to read the status of one or all of the internal relays. A ‘1’ indicates the relay is

SPECIAL APPLICATION400-0384-00313Example:Subroutine 10 is assigned to Input #1, subroutine 20 is assigned to Input #2, subroutine 30 is assigned to In

SPECIAL APPLICATION400-0384-00314Example:Subroutine 20 is labeled “RLY_1_ON”. The subroutine contains the function “WRRL1=1”. Send the command [RDS20]

SPECIAL APPLICATION400-0384-0031520. [SETTIME]This command sets the time for the PE1005 internal clock. The time is saved and displayed in 24-hour fo

SPECIAL APPLICATION400-0384-0031625. [RDDATE]This command reads the date from the internal clock.Command Format: [RDDATECi]Ci = Unit ID (i = # from 1

SPECIAL APPLICATION400-0384-00317Example:Associate Alarm #1 with subroutine 10 and set Alarm #1 to trigger at the bottom of every hour by sending the

SPECIAL APPLICATION400-0384-00318Example:Associate Alarm #1 with subroutine 10, and set Alarm #1 to trigger at 10:00AM every Tuesday, by sending the f

SPECIAL APPLICATION400-0384-0031TABLE OF CONTENTSPagePRECAUTIONS / SAFETY WARNINGS... 2GENERAL...

SPECIAL APPLICATION400-0384-00319Alarm #2 is now enabled and running. Every hour when the minute and second count matches “30:00”, the functions store

SPECIAL APPLICATION400-0384-00320ALARM CONTROLS36. [ALRMON]This command activates Alarm #1 and Alarm #2. After turning the alarm on, the functions as

SPECIAL APPLICATION400-0384-00321Hex characters can be added to the string by using the % sign in front of the hex number. Sending %0C will send the h

SPECIAL APPLICATION400-0384-00322Upon completion, the following message will be displayed.TASK COMPLETED 45. [CLRLM]This command clears one or all RS

SPECIAL APPLICATION400-0384-00323Command Format: [OUTPDPMmCi]m = Memory Location (m = # from 1 to 99)Ci = Unit ID (i = # from 1 to 99)Example:Send the

SPECIAL APPLICATION400-0384-00324MOTION DETECTORMDON, MDOFF, MD1, MD0, SETMD RDMDThe next commands setup and control the motion detector. [SETMD] sets

SPECIAL APPLICATION400-0384-00325Command Format: [SETMD=xCi]x = Time Delay (x = # from 01 to 99)01 = 0.1 minutes (6 sec)02 = 0.2 minutes (12 sec)…99 =

SPECIAL APPLICATION400-0384-00326REMEMBER: A command sent without the unit ID will be executed by all the PE1005s connected to the RS-232 port.66. [S

SPECIAL APPLICATION400-0384-0032746) [MODERSI] Set internal baud rate47) [RDRSI] Read internal baud rate48) [OUTRSM] Send memory data via external R

SPECIAL APPLICATION400-0384-00328Example 2: Adjust BrightnessNow that the plasma is in adjustment mode, various settings may be changed. Set the brig

SPECIAL APPLICATION400-0384-0032PRECAUTIONS / SAFETY WARNINGS 1Please read this manual carefully before using your PE1005. Keep this manual handy for

SPECIAL APPLICATION400-0384-003298.3 INPUT PORTS DO NOT RESPONDCause 1: The input pin is not grounded.Solution: Short the input port to ground using

SPECIAL APPLICATION400-0384-0033ABOUT YOUR PE1005 2PE1005PIONEER CONTROL CARDThe PE1005 Pioneer Control card allows users to control events on Pioneer

SPECIAL APPLICATION400-0384-0034DESCRIPTION OF PE1005 4APPLICATION DIAGRAMS 5DIAGRAM 1: TYPICAL SETUPCONNECTORRJ-45 NETWORK JACKCONNECTORTCP/IPDIGITAL

SPECIAL APPLICATION400-0384-0035DIAGRAM 2: INTERNAL VIEWETHERNET RJ-45USBTX/RXRC-232RS485TX/RXTXTXTXTXTXTXTX PDPRX PDPRX VIDEO CARDTX VIDEO CARDEDGE C

SPECIAL APPLICATION400-0384-0036DIAGRAM 3: CARD DETAILSLED1BATTERY3V LithiumCR1225P3Test connectorused for circuit card evaluation.SW1RS-232/RS-485 se

SPECIAL APPLICATION400-0384-0037DIAGRAM 4: 25-PIN HD DETAILSPIN Description PIN Description1 Input 1 5 Relay 1 Throw2 Input 2 6 Relay 1 Pole3 Input 3

SPECIAL APPLICATION400-0384-0038INSTALLING YOUR PE1005 6Step 1. Turn off the power to the plasma display. Step 2. Use ESD safety precautions and alway